Maxx Ice MIM130 Manual de uso y cuidado

AUTOMATICICE CUBE MACHINEUser’s ManualModels: MIM75/MIM100/MIM130*Be sure the ice machine has been standing upright for at least 24 hours prior to plu

8 Location Requirements To ensure proper ventilation for your ice maker, the front of the unit must be completely unobstr

9        In general, it is always a good idea to filter the water. A water filter, if it is of the proper type, can remove ta

10 Electrical Shock Hazard Plug into a grounded 3-prong outlet. Never remove the ground prong from the plug. Never use an adapter. Never use an ex

11 equipped with a power supply cord having a NEMA 5-15P 3-prong grounded plug. To minimize possible shock hazard, the cord must be plugged

12 outlet directly behind the ice maker will make under-counter installation easier. NOTE: 1. All installations must be in accordance with local plu

13 1. Find the floor drain near the ice maker. The distance should be less than 10 feet (3.5M) as the length of the long drain water pipe provided w

14 Installation Types This ice maker has been designed for Mobile (free-standing), Enclosed, or Built-in (sealed) installation. Mobile in

15 drain connections and the nut of the drain water hole. Tighten any connections or fittings that leak. 5. If electrical outlet for the ice m

16 Operating Method 1. Switch on the Power switch on the front panel. The light will be on. The ice maker will start working automatically a

17 hot gas valve and water inlet valve open to warm up the freezing surface, allowing the cubes to fall into the bin. Once completed, the freeze cycl

TABLE OF CONTENTS Page ICE MAKER SAFETY...

18  The high-efficiency compressor may make a pulsating or high-pitched sound.  Water running from the water bin to the evaporator plate

19 Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on no

20 Commercial grades of stainless steel are susceptible to rusting if not properly maintained. It is important that you properly care for

21 Condenser Cleaning A dirty or clogged condenser prevents proper airflow, reduces ice making capacity, and causes higher than recommended oper

22 SPRINKLER HEAD CLEANING NOTE: The sprinkler should only be cleaned when you find that some of the ice cubes are improperly shaped

23 4. Find which water sector is not spraying correctly from the nozzle. If the slideway is the issue, adjust the position of sl

24 10. Reassembly the sprinkler arm, slideway and the flake covers. 11. After the Icemaker System Cleaning procedure below. Ice Making System Cleani

25 The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-based cleaner products. Use rubber gloves to protect hands.

26 1. Prepare a sanitizing solution made of 1oz (29ml) of household bleach and 2 gallons (7.5L) of hot water 95ºF (35°C) to 115ºF (46°C). Remove t

27 longer. Turn the knob counter-clockwise, and the ice size will be smaller in the next cycle. NOTE: It is not a good idea to adjust the ice size of

1 ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual

28 TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this manual firs

29 Troubleshooting Guide Problem Possible Cause Probable Correction The machine doesn’t operate The ice maker is unplugged. Plug the ice maker in

30 Water is leaking from the unit. A few water drops fall to the floor when you open the door to take out ice from ice storage bin. Normal condens

31 The ice maker stops suddenly while making ice. The electricity is off. Reconnect the power supply line. The room temperature is out of the stat

32 Tested and certified to NSF standard 12 by NSF International

MAXXICE3355 Enterprise Avenue, Suite 160 Weston, Florida 33331Tel: 954-202-7419 - Fax: 954-202-7337

2 IMPORTANT SAFEGUARDS Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the

3 Code and local codes and ordinances is required.  Do not kink or pinch the power supply cord between the ice maker and cabinet.  The circuit br

4 receptical. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or

5 INTRODUCTION The Maxx Ice MIM series Ice Maker finds wide application in households, bars, restaurants, hotels, supermarkets, etc. It produces cry

6 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these bas

7 ICEICE MAKER INSTALLATION Unpacking Remove packaging materials NOTE: Do not remove any permanent instruction labels or the data labe